New Standards for School Bus Seat Belts
In October, the remaining provisions of NHTSA’s final rule on school bus occupant protection go into effect. Here, seat belt manufacturers discuss the changes.
One new testing requirement for belted school bus seats is to pull all of the belts at the same time. Pictured is a test at SynTec Seating Solutions.
Three years ago, the federal government issued several new requirements related to school bus occupant protection.
Two of the key provisions in the final rule, from the National Highway Traffic Safety Administration (NHTSA), went into effect in 2009. One required that all new school buses be equipped with 24-inch-high seat backs, which was a 4-inch increase on the height previously mandated. The other requirement starting in 2009 was for self-latching seat bottom cushions on new school buses.
The other two key provisions of the final rule are set to go into effect on Oct. 21 of this year. One will require school buses weighing 10,000 pounds or less to have lap-shoulder belts. The other sets new standards for the testing and design of school bus seat belt systems to ensure the strength of the anchorages and the compatibility of the seat with compartmentalization (the passive protection provided by school bus seating compartments).
In advance of the new standards, school bus seat belt manufacturers have made improvements to their products, and they say that the result of the rules will be increased safety for students.
Rigorous testing
One component of the school bus seat belt standards is quasi-static testing.
“In a nutshell, it’s loading the back of the school bus seat as though an unrestrained child has gone forward and hit the seat, and at the same time pulling the seat forward” to simulate a restrained child, explains Robert Knapp, executive vice president of the C.E. White Co.
Knapp says that while C.E. White’s belted seat has met that test for many years, the company has redesigned theseat. It’s now narrower – taking up the same amount of space as a seat without belts – and is 20 pounds lighter than it used to be. Also, the same seat frame can be used with belts or without belts, in which case belts can be added later if needed.
Charlie Vits, market development manager for IMMI’s SafeGuard brand, says that the SafeGuard seats already achieve the levels of occupant protection that the new standards are based on. But the company has taken the opportunity to develop its new SafeGuard XChange seat.
“Beyond meeting performance and design requirements, the design has been changed so that a SafeGuard base seat can be easily converted to a lapshoulder belt or integrated child seat configuration,” Vits explains.
Brandon Marriott, general manager of SynTec Seating Solutions, says that NHTSA’s final rule, in particular the quasi-static testing, “is forcing a balance between seat belt load and compartmentalization, which is very important. You don’t want to expose children who aren’t wearing their seat belts to additional risk.”
SynTec manufactures M2K brand seats, which Marriott says were “designed for these tests from the beginning.”
Another new testing requirement, for FMVSS 210, is to pull all seat belts on a seat at the same time. Prior to the October 2011 provision going into effect, certification only requires pulling the seat belts sequentially.
The simultaneous pull “makes for a more complicated test setup,” Marriott notes, “and requires more expensive equipment.”
Ensuring safety
Although the seat belt manufacturers say that their products already met the new performance requirements, they agree that NHTSA’s final rule enhances the protection of school bus passengers and that the testing standards are important.
“It absolutely increases safety,” Marriott says. “This is something that the industry itself should be very proud of – it’s advancing school bus technology.”
Vits notes that “from an industry perspective, we now have a standard that ensures a level of performance and thus safety from all lap-shoulder belt seats.”
Knapp says that one of the most important aspects of the new ruling is that “it allowed us to keep the seats narrower at the top, which is very important for emergency egress. That’s the part that pleases me the most about it.”
Belts in small buses
While seat belt manufacturers say that the new requirement for lap-shoulder belts (instead of just lap belts) on school buses weighing 10,000 pounds or less is a move in the right direction, some say it should have gone further.
If you appreciated this article and want to receive more valuable industry content like this, click here to sign up for our FREE digital newsletters!
Related Content
Leading in Turbulent Times: Effective Campus Public Safety Leadership for the 21st Century
This new webcast will discuss how campus public safety leaders can effectively incorporate Clery Act, Title IX, customer service, “helicopter” parents, emergency notification, town-gown relationships, brand management, Greek Life, student recruitment, faculty, and more into their roles and develop the necessary skills to successfully lead their departments. Register today to attend this free webcast!
